Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterTrusted Gate Parts & Welding for Malibu Homeowners
A sagging gate, a hinge that screams every time the wind moves, a weld that finally gave out after years of salt air off the Pacific - in Malibu, these aren’t annoyances, they’re daily realities. Our Gate Parts & Welding in Malibu is the difference between a gate that works for another ten years and one that dumps itself onto your driveway at midnight. We’ve been fixing gates since 2001, and we’ve seen what the coastal climate does to steel and iron. When your gate hinge tears or your post shifts in the hillside clay, you want someone who welds on site, fixes the actual failure, and doesn’t upsell you a new gate you don’t need. Call (559) 314-7708 and Hal Gatewood will answer. A live person picks up, day or night.
What Our Gate Parts & Welding Service Includes
Most gate failures come down to one worn part or one failed weld. We replace the part, we weld the joint, and the gate goes back to working. Here’s what that actually looks like, piece by piece.
Hinge Replacement
Hinges carry the entire weight of the gate, and in Malibu’s salt-air environment they corrode faster than anything else on the property. When a hinge wears, the gate drops at the latch side, drags on the ground, and eventually binds against the post. We replace hinges on site, cutting out the old weld, squaring the gate in the opening, and welding in new hinges that’ll hold up to coastal weather. Hal picks the hinge weight for the gate, not for the bid - undersized hinges are the most common shortcut we see.
Post Replacement
A gate sags in the hinge post, not in the middle - and that’s where we start. In Malibu, posts set in hillside clay or sandy loam lean over time, especially when they weren’t buried deep enough to begin with. We pull the old post, dig a proper footing, set the new post straight and plumb, and weld or bolt the gate back to it. If the post is steel, we weld it; if it’s wood, we rebuild the mounting plate and through-bolt it so the hinge load sits on the post, not on screws.
Rail Repair
Rails are the horizontal members that keep the gate square, and when a rail rots out or snaps at a weld, the whole panel flexes and the latch stops lining up. We repair rails by welding in new steel, straightening bent sections, or replacing the rail entirely when corrosion has gone too deep. The key is matching the repair to the failure - a welded splice that doesn’t address the rust at the joint will fail again in a season. We cut back to clean metal, weld the new section, and treat the area so it lasts.
Custom Welding
Not every gate part comes off a shelf. When a Malibu or Gate Parts & Welding in Westlake Village driveway gate has an odd angle, a historical iron design, or a motor mount that no longer matches the new opener, we weld the part in the driveway, on the spot. Hal’s been welding since 2001, and he brings the rig to you - the gate doesn’t leave your property. Custom brackets, extended hinges, reinforced corners, replacement scrollwork: if it’s steel, iron, or aluminum, we can weld it back to working.
Gate Rollers
Sliding gates roll on wheels, and those wheels wear flat, seize on their bearings, or clog with sand and salt spray. When a roller fails, the gate gets harder to move until the motor burns out or the track bends. We replace rollers, check the track alignment, and adjust the whole assembly so the gate glides instead of grinding. In Malibu’s coastal wind, a sliding gate with bad rollers becomes a sail - fixing the rollers takes the strain off everything else, including the motor.
Latch & Lock
If the latch doesn’t catch, the gate doesn’t stay shut, and in Malibu that means deer in the garden or wind slamming the gate until something bends. We replace latches, rebuild striker plates, weld on new lock boxes, and re-align everything so the bolt lands where it should. Locks get crusted with salt air and stop turning - we clean, lubricate, and replace cores when they’re beyond saving. A gate that latches and locks properly is a gate that doesn’t beat itself apart in the first Santa Ana.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Gate Parts & Welding
We service nine major gate brands, and we’ve been certifed to work on all of them: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. When you call about a BFT slide gate that’s welding off its track or a hinge that’s separating from the post, we know where to look and we stock the OEM parts to fix it right. Hal has worked on Linear swing gates up and down the Malibu coast, and we keep their common hinge and roller parts on the truck so we’re not running back to the shop mid-repair.
On Viking and Ghost Controls gates, we’ve handled everything from broken welds on the operator mount to post replacements that require re-hanging the entire leaf. The brand matters less than the workmanship - whether you have a Ghost Controls cantilever gate or a Viking swing, we’ll match the metal, match the part, and weld it so it holds. If your gate is from any other make, we’ll still fix it. The weld doesn’t care whose name is on the box.
Signs You Need Gate Parts & Welding Right Now
Some gate problems announce themselves. Others creep in quietly until something breaks. Here’s what to watch for on a Malibu property.
- The gate drags or scrapes when it opens. A gate that drags is telling you a hinge is worn, a post has leaned, or a roller has gone flat. Every scrape is metal wearing away - the longer it drags, the more material you lose and the more expensive the fix becomes.
- The latch doesn’t catch anymore. When the bolt misses the strike plate, the gate swings free in the wind and slams against stops or fences. A slamming gate bends hinges, cracks welds, and eventually tears the post out of the ground. The latch is the first thing to fail and the easiest thing to ignore.
- You see rust bloom at the welds. Salt air in Malibu gets into every seam and joint, and a weld with surface rust is a weld that’s losing strength underneath. By the time you see flaking rust, the cross-section has thinned. That’s the repair window closing - catch it before the weld cracks through.
- The gate sags toward the latch side. A gate that sags is almost always a hinge-post problem, not a panel problem. The post leans, the hinges carry uneven load, and the gate drops. Fix the panel without the post and you’ll fix it twice - we look at the post first.
- The gate shakes or wobbles while moving. Loose hinge bolts, worn pivot pins, or a cracked weld all show up as shaking in motion. A gate that shakes is stressing every connection along its length, and one of those connections will fail soon. Better to find it now than to have the gate come apart in a windstorm.
Our Gate Parts & Welding Process - Step by Step
When you call Gatewood Fence & Gate, here’s how the job actually goes, from the first call to the final weld.
- 1
You call, Hal answers. A live person picks up the phone 24 hours a day, seven days a week. No voicemail, no automated menu, no call center. Hal will ask what the gate is doing, get your address if it’s in the county, and tell you when he can be there.
- 2
We show up and look. We come to your Malibu property and inspect the gate in place. Hal checks the hinges, the posts, the welds, the rollers, the track, and the latch. He’ll tell you what’s actually wrong - not what’s easiest to bill. If it’s a hinge, he says hinge. If the post is the problem, he’ll show you the lean.
- 3
You get a written price before any work starts. The quote is the price, and the price is the quote. No surprises at the door, no “we found more problems” phone calls. If additional work is needed, we discuss it with you first and you approve it in writing before we touch it.
- 4
We do the work on site. The gate stays in your driveway. Hal welds it there, cuts out the bad section, replaces the part, and re-hangs everything square and plumb. No hauling the gate off to a shop, no week-long wait. For most repairs, the job is done the same visit.
- 5
You get the 90-Day Done Right Promise in writing. Every job comes with our 90-Day Done Right Promise, stamped on the invoice. If it’s not done right, we make it right. One call brings Hal back, no runaround. The name is on the shop, and the shop is down the road.
How Much Does Gate Parts & Welding Cost in Malibu?
If you’re wondering how much Gate Parts & Welding costs, pricing in Malibu runs on a pretty honest scale - the part, the labor, and the weld. A typical hinge replacement runs $180 to $340 depending on the gate weight and how many hinges are involved. A full post replacement, with digging, concrete, and setting the gate back square, runs $450 to $900 depending on the post material and the excavation. A rail repair or custom weld generally falls in the $250 to $500 range, depending on how much steel we’re cutting out and how much new material we’re putting in. Roller replacement runs $150 to $300 per roller, including the track adjustment. Latch and lock work typically runs $120 to $280.
What changes the price? Gate weight and height come first - a 400-pound hardwood gate needs bigger hinges, a stronger post, and more weld time than a light aluminum tube gate. Access matters too: if we’re working on a hillside driveway in Malibu where setting up the welder means a 50-foot run from the truck, that’s different from a flat, open drive. The condition of the existing metal changes things as well: if the old welds are rusted through and we’re cutting back twice as much to find clean steel, that’s more time and more material.
How do you avoid overpaying? Ask whether the repair addresses the actual failure or just patches the symptom. A hinge replacement that doesn’t check the post is a repair that’ll fail again. Get the price in writing before work begins - that’s how we work anyway. And remember, we offer $40 off any repair over $200, and no trip charge inside the county. If you’ve already got a written estimate from another company, bring it - we’ll give you a free second opinion. And seniors and veterans always get 10% off, permanently. Call (559) 314-7708 for an exact quote. The estimate is free.
Gate Parts & Welding Near Malibu - Our Service Area
We’re based close enough to Malibu to be at your gate fast, and we work throughout the county. We regularly handle gate parts and welding for homeowners in home territory - which is to say, right in your neighborhood, not a satellite office an hour away. From the coast to the canyons, we cover Malibu, Gate Parts & Welding in Westlake Village, Gate Parts & Welding in Agoura Hills, Calabasas, Topanga, Lake Sherwood, Oak Park, and Hidden Hills. Most calls get a same-day visit when you call before noon.
Serving Malibu, CA - Our Local Coverage Area
We’re based in the Malibu area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Gate Parts & Welding in Malibu
Gate parts and welding covers the repair and replacement of the structural metal components that make your gate function: hinges, posts, rails, rollers, latches, locks, and the custom-fabricated pieces that hold it all together. When a part fails, we replace it; when a weld breaks, we weld it on site. It’s the difference between repairing what’s broken and replacing the whole gate because nobody wanted to fix it.
Most hinge, roller, latch, and weld repairs are completed in a single visit, usually two to four hours depending on the scope. A post replacement takes longer because the concrete needs to cure before the gate is re-hung - plan on a day or two before the gate carries full load again. We’ll tell you exactly what the timeline looks like when we give you the written quote.
A typical hinge replacement runs $180 to $340, a post replacement runs $450 to $900, rail repair and custom welding run $250 to $500, roller replacement runs $150 to $300 per roller, and latch and lock work runs $120 to $280. The exact number depends on gate weight, access, and the condition of the existing metal. Call (559) 314-7708 for an exact quote - estimates are free and the price is quoted before any work starts.
Yes. We’re certified to service all nine major gate brands, including BFT, Linear, Viking, and Ghost Controls. We stock OEM parts for those brands on the truck, and Hal has welded and repaired hundreds of their gates throughout Malibu and the surrounding county. If your gate is a different make, we’ll still fix the weld or replace the part.
Yes. A live person answers our phone 24 hours a day, seven days a week. If your gate is stuck open, hanging off its hinges, or won’t latch, Hal will get to you the same day in most cases. When you call (559) 314-7708, you’re talking to a person who can be in a truck headed to your Malibu property within the hour.
Every gate parts and welding job comes with our 90-Day Done Right Promise, in writing. If something isn’t done right - a weld cracks, a hinge we installed loosens, a latch we set doesn’t catch - one call brings Hal back to make it right. No runaround, no fine print, no “that’s not covered.” If we fixed it and it didn’t hold, we fix it again on us.
Clear the area around the gate so Hal can get to both sides - move cars, bikes, trash bins, and anything that blocks the swing path or the sliding track. If the gate is automatic, have the opener unplugged or the breaker off so he can work safely. You don’t need to remove anything from the gate itself, and you don’t need to be home if you’ve already approved the quote.
Schedule Your Gate Parts & Welding Service in Malibu Today
Call (559) 314-7708 and you’ll get Hal or a member of his crew on the line - a live person, day or night. We’ll talk about what your gate is doing, schedule a visit, and give you a written price before any work starts. There’s no charge for the estimate, no trip charge inside the county, and every job is covered by the 90-Day Done Right Promise. Call today.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Malibu since 2001.