Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterViking Gate Parts & Welding in Malibu: What to Know First
We provide independent Viking gate parts and welding in Malibu, and most hinge replacements, post repairs, and custom weld jobs are done on site within a day or two of your call. You’ll know the price before we touch anything because we quote the work, you approve it, and then we start. If you own a Viking gate anywhere from Point Dume down to the Malibu Colony and something’s cracked, sagging, or torn loose, call (559) 314-7708 and a live person answers. This page is for Malibu homeowners who need straight answers about Viking parts, welding, and whether a repair makes more sense than a replacement. We are an independent Viking service provider, not a manufacturer authorized shop, which means we fix what’s actually wrong instead of pushing a new gate.
How Viking Products Fail - and How We Fix Them
Viking gates are common along the Malibu coast, and after twenty-plus years of working on them, we know exactly where they give out. Here’s what we see most often.
- Hinge welds cracking on Viking R-6 and R-20 series swing gates. The salt air out by Point Dume doesn’t just sit on the surface, it works its way into the weld seam and eats from the inside. We grind the old weld back to clean steel, weld the hinge with a 7018 rod, and add a small gusset so the next decade doesn’t start with the same call.
- Bottom rail rot on Viking estate gates near the coast. The factory welds are fine, but the weep holes get plugged with sand and salt spray, water sits in the rail, and the bottom rots from the inside while the outside still looks painted. We cut the bad section out, weld in a new rail with proper drainage, and the gate goes back up straight.
- Post failure from Malibu’s hillside grading. A Viking gate is heavy, and when it’s hung on a post set in loose canyon fill, the whole post leans and the gate starts dragging. We reset or reinforce the post, often welding a steel sleeve at the base, so the post holds the gate instead of the gate holding the post.
- Stripped threads on Viking latch and lock mounts. Over time, the tapped holes on the gate frame hog out, and the latch plate wiggles loose every few weeks. The quick fix is a bigger screw, but that lasts a season. We weld a proper backing plate in place and redrill, so the latch stays put.
- Roller wear on Viking sliding gates. The factory rollers are decent, but Malibu’s sand and salt make short work of the bearings. When the gate starts grinding instead of rolling, we replace the rollers with sealed-bearing aftermarket units that handle the grit better than original equipment.
Our Viking Gate Parts & Welding Process
Every Viking job we do follows the same path, and nothing is a surprise by the time we’re done.
- 1
You call, we talk. A live person answers at (559) 314-7708, day or night. You tell us what the gate is doing wrong, and we’ll tell you what it likely needs before anyone drives out.
- 2
We come out and look. We schedule a window and show up in it. Hal or one of his crew gets the gate moving, checks the hinges, posts, rails, and rollers, and figures out the actual failure, not just the symptom.
- 3
You get a written price. We quote parts and labor in writing, and that price is what you pay. No trip charge inside the county, and if you’ve got another written estimate, we’ll give you a free second opinion on it.
- 4
We fix it on site. For most Viking hinge, post, rail, and roller work, the welding happens right in your driveway. Your gate stays on your property, and you can watch the whole thing if you want.
- 5
We test it hard. We run the gate through full cycles, check the welds, check the clearances, and make sure it opens and closes like it should. If it’s a motorized Viking gate, we test the limit settings and safety edges too.
- 6
You get the 90-Day Done Right Promise in writing. If something isn’t right, one call brings us back. No runaround, no fine print.
What Viking Gate Parts & Welding Costs in Malibu
Viking gate repairs in Malibu usually run between $250 and $900 depending on what’s failed and how much weld time is involved. Here’s a practical breakdown:
- Single hinge re-weld: $180 to $300, including grinding, welding, and touch-up paint.
- Post reinforcement or replacement: $400 to $900, depending on whether we’re sleeving the existing post or setting a new one in concrete.
- Bottom rail section repair: $300 to $600, including cutting out the rot and welding in new steel.
- Roller replacement (sliding gate): $200 to $450 per set, depending on the gate weight and track condition.
- Latch and lock plate re-mount with backing plate: $150 to $300.
What moves the price is how much weld time the job takes, whether we’re working on a hillside, and whether the post itself has to be dug out. You’ll always get the number before we strike an arc. Call (559) 314-7708 for an exact quote, and remember: $40 off any repair over $200, and a permanent 10% discount for seniors and veterans.
Why Malibu Homeowners Call Gatewood Fence & Gate for Viking Work
Hal Gatewood has been fixing gates up and down the Malibu coast since 2001, and most of his regulars know him from the stretch of properties out past Point Dume where he’s sorted out more salt-rusted hinges and stripped motor gears than he can count. He picked up the trade at Santa Monica College, running through their vocational and applied technology programs, and he’s been owner-operated ever since. The name is on the shop, and the shop is down the road, which is the oldest accountability there is.
We service Viking plus four other major brands, LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so when a Malibu property has a Viking gate on one entrance and something else on another, one call covers it. The 90-Day Done Right Promise is on every invoice in writing. Calls are answered by a live person 24/7. And if you’ve got questions about a Viking gate part we didn’t touch, Hal will tell you honestly whether it’s worth fixing at all. Tell me what it’s doing wrong and I’ll tell you what it actually needs, no runaround.
FAQs
Yes, we can source Viking OEM parts, and we often recommend them for motor and control board work. For hinges, rails, and rollers, we frequently use high-quality aftermarket parts with sealed bearings or better steel because they handle Malibu’s salt air better than the factory originals.
Most of the time, yes. Hinge re-welds, rail repairs, and latch mounting are done with the gate in place in your driveway. We only pull a gate when the work requires laying it flat, which is rare. Welding on site keeps the gate aligned and saves you the hassle of a crane or a truck bed. Call (559) 314-7708 and we’ll tell you whether your specific repair needs the gate off the hinges.
Welding is almost always cheaper than replacing, typically a third to half the cost of a new gate. A gate sags in the hinge post, not in the middle, and that’s where we start. If the post is solid and the frame hasn’t rotted through in multiple places, welding gets you another five to ten years. We’ll tell you straight if yours is past a weld.
For a hinge that’s torn loose or a gate dragging so badly it won’t open, we typically get there same day or next day. Malibu’s canyon roads and coastal traffic can add time, but we live and work in the area, so we’re not coming from across the county. Call (559) 314-7708 and a live person answers around the clock.
If your Viking gate is still under manufacturer warranty, a structural repair by an independent shop may affect coverage on the welded component. We’ll walk through exactly what’s covered and what isn’t before any work starts, and we’ll put our 90-Day Done Right Promise on everything we touch. We are an independent Viking service provider, so nobody here is going to pretend otherwise.
Written by Hal Gatewood, Owner, Gatewood Fence & Gate at Gatewood Fence & Gate, serving Malibu and nearby areas.